Uusi muovikolvi ja ruosteet – Audi S2 ep19

Hi, everything should be ready for this evening which we spend on the garage repairing S I send email to Az-Reptec where I bought those bumper repair rods If they could send me their welding iron So I could do better repairs to that bumper and install that support mesh easier well they did send […]

How to make a mini Hydrogen Generator / TUTORIAL

您需要準備這些東西 2個同尺寸的冰棒棍 在棍面上畫上鑽孔點 再叧一根棍面上重做一次 再穩穩的將兩根冰棍壓緊 鑽孔 鑽孔後就像這樣 每相隔一個孔鎖上一個螺絲並穿過兩冰棍 再換面重做一次 再螺面上焊上錫點(可視螺絲材質選用合適的錫) 換面重做一次 然後 再螺面錫點上焊上電線 現在 可以將導電模組放入玻璃瓶中 瓶蓋上要鑽一個合適孔徑的洞 拿出西藥房買的滴管組 切掉上端 將電線穿過瓶蓋開孔 再將滴管組的觀察室塞進孔中,盡量塞緊 再用熱融膠封口,確保氣體不外洩 鎖緊瓶蓋 再依據實際需求剪截滴管 在集氣瓶鑽2個合適大小的孔 將滴管末端由孔1塞入瓶中 一定要將管子穿到瓶底 再將裁剩的那截滴管由孔2穿入瓶內.不必穿太深 再以熱融膠封口 這時 可以倒入清水了 蓋上瓶蓋 取一些鹽加水攪均 再打開瓶1 (導電模組) 倒入剛才自製的鹽水(導電液) 要淹滿整個導電模組 鎖緊瓶蓋 現在可以將電線接上電源供應器了 調整輸出電壓為 2.1 伏特 現在 您會看到瓶內開始有汽泡產生 (泡泡測試)

Vanha etupuskuri.. UUSI kamera – Audi S2 ep17

Think the camera is on… Hello, I’m Asko and this is sweatpants garage I’m so exited. I have new camera Don’t know how to use it and the mic is still on the way So we have to use this mic But we hit the 5000 subscriber mark big thanks to You all! apparently subscriber […]

HOW to make an arc welding machine using the toroidal transformer of an amplifier, Power core

Hello all of you. Today I go back to the topic of power supplies for amplifiers and electric arc welding machines. That is the power supply for the high power amplifier that I made in the previous video. Use toroidal transformer to make arc welding machine. It is a toroidal transformer. I removed this toroidal […]

Miller Users Weld for Performance

(upbeat music) – I’m Dan Reiger, I’m a welder at the Bobcat Company in Gwinner, North Dakota. Bobcat’s been around for 60 years. I’ve been with Bobcat for 27 years myself. Anything I do I like to be consistent in my welding. My wife calls me a perfectionist. Miller, it makes my work better, my […]

DIY CNC Router on Certiflat Welding Table Part 9: Update Running Linux

hey YouTube so it’s been about a year and a half since I did it in videos on the third flat CNC machine and frankly I haven’t done anything with it since then it’s been kind of a workbench and catch-all for storm throwing stuff on top of table I ran into a project the […]

How To Solder a 3.5mm, ⅛”, or Mini Headphone Connector

Hi I’m Benson with Linxus Communications Today we’re going to teach you how to correctly solder at 3.5 millimeter connector the 3.5 millimeter connector also known as mini plug ⅛” Jack or your common headphone jack can be used to plug into an mp3 player a CD player or a stereo. For this project you […]