Rotary Tumblers & Stainless Steel Tumbling Media – OPERATION

rotary tumblers and stainless steel tumbling media clean brass reload brass rotary tumblers and stainless steel tumbling media clean brass reload brass reloading brass reloading equipment rotary tumbler tumble brass best brass cleaner brass cleaning equipment brass cleaning machine

Chimney Liner Installation for Fireplace Insert Stainless Steel

The liner is down in here now, and we’re going to attach this A connector to it, the liner slips in between, and allows the creosote to run back into the stove, anyway, I’ll just show you that. Now, we might have to use crimpers on the Z Flex to get it to fit in […]

First Look: APOLLO Stainless Steel Safety Razor

Here is the first look at the Smart Helix Razor from the Ukraine. Nice packaging! Fancy, very cool packaging. Apollo stainless steel razor that’s beautiful it’s like a little tombstone or a little casket for your razor opens from the top with a fitted cover Awesome, beautiful! Okay let’s remove that. It comes with a […]

What’s in my (PPE) bag? Heavy Duty Marine Mechanic’s Personal Protective Equipment

Today on Repairs101 I’m going to show you what’s inside my Personal Protective Equipment bag. OK you can see I did a much better job of keeping this one clean than I did with my tool-bag. It’s because I don’t carry it everywhere I just keep it under whatever bench I’m working on. So the […]

How to make a mini Hydrogen Generator / TUTORIAL

您需要準備這些東西 2個同尺寸的冰棒棍 在棍面上畫上鑽孔點 再叧一根棍面上重做一次 再穩穩的將兩根冰棍壓緊 鑽孔 鑽孔後就像這樣 每相隔一個孔鎖上一個螺絲並穿過兩冰棍 再換面重做一次 再螺面上焊上錫點(可視螺絲材質選用合適的錫) 換面重做一次 然後 再螺面錫點上焊上電線 現在 可以將導電模組放入玻璃瓶中 瓶蓋上要鑽一個合適孔徑的洞 拿出西藥房買的滴管組 切掉上端 將電線穿過瓶蓋開孔 再將滴管組的觀察室塞進孔中,盡量塞緊 再用熱融膠封口,確保氣體不外洩 鎖緊瓶蓋 再依據實際需求剪截滴管 在集氣瓶鑽2個合適大小的孔 將滴管末端由孔1塞入瓶中 一定要將管子穿到瓶底 再將裁剩的那截滴管由孔2穿入瓶內.不必穿太深 再以熱融膠封口 這時 可以倒入清水了 蓋上瓶蓋 取一些鹽加水攪均 再打開瓶1 (導電模組) 倒入剛才自製的鹽水(導電液) 要淹滿整個導電模組 鎖緊瓶蓋 現在可以將電線接上電源供應器了 調整輸出電壓為 2.1 伏特 現在 您會看到瓶內開始有汽泡產生 (泡泡測試)

Engine Porting Kit & How To DIY from Eastwood

Today we’re gonna talk about something that may be magic to some others might just be the normal course of building a motor but it’s porting a cylinder head you’ve already upgraded exhaust carburetor maybe even a cam now what you want to do is get the most efficiency you can out of better flowing […]

PART 2 73-87 C10 RUST REPAIR | Welding Chevy Patch Panels

Ok, here’s another video I’m posting about my Rust panel, patch panel work Rust repair work I’m doing On my 77 half ton C10 And I wanted to show you guys I made a mistake here And I wanted to document this So others don’t make this same mistake Basically what I did was I […]

Plastic Welding with Ease » Weld and repair a playground Slide using a plastic welder

Hi, I’m Bruce Lecky from Drader Manufacturing and I’m going to use the Drader Injectiweld to repair a damaged playground slide. My first job is to clean the damaged area. For maximum weld strength I’m going to use a grinder and a scraper to grind away the oxidization and the debris. The Injectiweld has a […]

Dent Repair How To DIY with MIG Stud Weld Kit from Eastwood

what we got here is our early Mustang you can see we put a quarter panel on it now we came up here to the door area grounded down to it looked ok once we got all the filler off because these two sharp creases we don’t have money for a new skin so we’re […]

Rust Repair Panel DIY – Patch Panel & Installation Kit for your Car from Eastwood

all right today what we’re going to do is sew sew a patch panel here get this mg fender here with a guy wants to repair and you can see it’s a lot of legwork and from the back side we saw a lot of holes back here so we gotta cut this out a […]