Spot Welding Tips, Rust Removal and DIY Garage Tips on Mark’s R&D Corner from Eastwood, Episode 1

Spot Welding Tips, Rust Removal and DIY Garage Tips on Mark’s R&D Corner from Eastwood, Episode 1


Mark here product manager at Eastwood and what we’re going to do is show you some tips and tricks to help around the shop and also some great new products let’s get started first thing we’re going to show you is basic it cutting with the hacksaw here’s what is your cutting a round object like
this if this were nice if this were nice
machine finish or plated you’re going to end up sliding off
until you get a groove going Take your thumb and lay it down there you can not cut your nail on a vertical it gives you the perfect starting point everytime you lay it down on your cutline it works on round objects or square next thing drilling holes as simple as it may seem everyone’s ran into it here’s where i wanted my
hole here’s where it actually went here’s a trick, always drill your holes with
pilots i like to use a three sixteen you go um… use an eighth whatever bit you want start on it now with a hole
like this what you can do is you can move that simply get an angle and move slow we can move it as far as you want, when you get back to the center point turn it right back up now you’re back on center as you can see there and then when you come in you’re finished size you’ll have the hole perfectly centered where you needed it now sheet metal you’re gonna be working on sheet metal a lot with your projects whether it’s automotive uh… general fab around the house drilling holes through sheet metal same thing you come through here once you have your punch-through you
can end up with a bur on the back side every time That’s what you’re gonna end up with So again easy way to clean that up drill bit twice the diameter by hand couple turns will pull that bur right off here’s another trick you’ll notice once you get into anything over three eighths round drill bits can drill triangular shaped holes in sheet metal it’s a phenomenon that nobody really
knows about but what we end up with is not what you wanted here’s the way to solve that problem start drilling your hole like we have here, we just started this one right when you feel the punch through right when you feel the tip break
through the metal like you see there, the small point if your project allows you flip it over then go ahead finish the hole from the opposite side eliminate the bur and you end up with perfectly round hole this works great especially with your larger
diameters, like I said, once you get into anything over three eighths go ahead punch through flip it over and finish it from the other side now what i want to do is talk about cotter pins simple little product can save your life or end it and cause disaster what I want to show you is a quick tip how a cotter pin is installed what we got here is just a typical upper ball
joint. It may look good but it’s totally incorrect There is only one way to install a cotter pin and one way to remove it simply use a pair of side cutters flatten it out pull it out in one piece when you install a cotter pin it can only go one way install it straight up same thing take your side cutters trim this one here this piece here you want no lower than your your castle nut right down there when you trim it just simply hold your hand over sides folded down same thing with this this side fold flat one-half diameter of the stud just roll that right over now let’s check out four of the latest tools
from eastwood now let’s take a moment to show you some great new products that we
got here at eastwood these things are new rust brush and what they do is tear off any coatings or rust simple to use simply put it into any three-eighths corded or cordless drill. Typical wire brushes is radial in fashion and about half inch thick
so you only have that half inch width that you’re cutting this thing is a full four inch so when you are remove any type of rust or coating as quick as that this is great for cleaning up frame or
suspension components or general all-around the shop useage we got a set of five of them here the cost is uh… just about the same as
what you pay for one spiral round brush so if you’ve got a project where you’re trying to
remove coatings or rust this is a must have system How familiar is this? anytime you change your oil whether it’s the
classic or daily driver this is what you end up with now let’s check Eastwood’s great solution The great thing about this tool it’s set up to utilize the traditional eight-inch
socket and what it does it has internal flutes to capture the filter and all the residual
oil. The bellows here allow different sizes different mounting pads of the filters now this eliminates that mess no more oil on your
hands, no more on the shop floor none of it on the late models leaking on
the suspension components or under body plastic your filter then simply removed and thrown away great product we have three different sizes that fit
about ninety percent of all the vehicle on the road today go ahead click the link below to get
your’s today anytime you working on automobiles doing any
collision or rust removal you’ll run into spot welds You’re all probably familiar with drilling them out
that’s a good time. But how about replacing them? best thing you can do is utilize our new Eastwood spot weld kit what this kit does is allow you to take
your mig welder and create OE looking but structurally sound spot welds. Look at the
backside full penetration through both panels and you end up with exact resistance type spot weld
that was original done at the factory the kit itself very easy we the specially designed clamping pliers these cutouts here, what that does is any type of pinch welds allows you to clamp and secure the pieces
together and this nozzle with these leg
extensions that we have machined into this is a current mig nozzle but you do is simply remove that install the eastward spot weld nozzle what these two legs give you is the exact standoff needed from the trip to the substrate every time this is what achieves the repeatability and
all the spot welds looking the same second feature of them is alignment once your panel is clamped here this allows you to come in and the legs position right into the clamping area you know exactly where the spot weld
will be every time but we also include his double ended three sixteen drill bits these are for doing plug welds
if you got a small welder or you’re working with some really heavy gauge
material what you do is take the top panel go ahead and drill your plug weld hole through that clamp them and using the tip do the same spot weld
through there, it insurers penetration through those panels now these pieces here this one is still warm
this is something that we just did I’m going to show you what you’re going to have to do to get these things apart literally you’re gonna have to tear the metal around those welds what we have right there that’s the only way these welds are coming apart so you can be assured you’re getting complete and the OE appearance you’re going after so go ahead click the link below to get your kit today

12 thoughts on “Spot Welding Tips, Rust Removal and DIY Garage Tips on Mark’s R&D Corner from Eastwood, Episode 1

  1. It fits any MIG welders with Tweco style consumables. I'd check with the manufacturer or your local welding supply store to see if that is the style your welder takes. Thanks for the interest- Matt/EW

  2. With this tool you're only welding for a short period of time (a few seconds), which if the machine is set correctly, shouldn't cause a issue with out of position welds. We suggest to do some test welds to dial in your settings on your machine. Using our suggested settings in the instructions is a good starting point, but you may need to tweak things a little if welding out of position. -Matt/EW

  3. Mark's an Eastwood Guy.  Are You?  Check out this video from Eastwood to find out:
    Dirty Harry Welder Dream – Stop Dreaming & Get A MIG Welder – Are You An Eastwood Guy?

  4. One of THE BEST vids on tips and such I've seen. ALL GREAT practical advise and tips we can all use. Thanks!

Leave a Reply

Your email address will not be published. Required fields are marked *