HHO Workshop “Free From Fuel”: Heating With Oxyhydrogen (DVD Chapter 2)

HHO Workshop “Free From Fuel”: Heating With Oxyhydrogen (DVD Chapter 2)


The flame recombines hydrogen and oxygen back into water again. Here it becomes water again. For about 4 years now I have heated
my house with this gas. People often bring this argument up:
“Why use electricity to create gas
and heat with the gas? Why don’t you just heat directly
with the electricity?” And so I researched to prove to
myself whether I was right or not. Official verification is up to Universities of course. I can only verify things for myself. It is this practical experience which gives me the
knowledge and assurance to explain what I am doing. Only then I can talk effectively about
the things I researched and had hands-on experience with. So I heated electrically for 2 years,
just to refute the argument of
“Why not to heat electrically?” And I can tell you, the electricity bill
went through the roof! Heating with conventional
electric heaters? No way! Last year I tried infrared heating panels. They are also electrically powered and are said to be very efficient,
which they were to an extent. But they definitely weren’t as efficient
as my Oxyhydrogen heater. What does that mean? It is said that electricity is 100% efficient. Now what about my Oxyhydrogen heater?
If I save more money with it, then it must be even more efficient.
Saving money means this, I usually have heating costs
of 1200 Euro each year. After 4 years of trial my annual costs
are down to 450 Euro every year. So, this isn’t just my imagination anymore.
This is factual proof. But imagine this:
I only heated one single room! And this is what I built. I call it the “Sand Heater”.
Nobody has seen this before. I just have to connect the tube… This is a tube entirely filled
with very fine sand. It’s a bit hot in this room already,
so I won’t keep it on long. First I have to ignite it from the top here. I’ve left the top open for you to see. Usually it is covered so
you wouldn’t see anything. It is hot already. Now if I hold a glass above this,
you can see condensation. This is escaping water vapour. It is up here that the sand burns. It gets very hot
and heats up the entire tube up to 70°C. All the way up.
It is very hot, you can feel that. You can hear a low popping sound from the platinated sand. This is simply platinum foil within the sand. I just have to pre-heat it.
And at 60°C the platinum starts to recombine the Hydrogen and Oxygen
without any flame. Now here we have the gas.
All entirely flameless. Just because of the platinum sand on top. It takes half an hour
to heat the entire tube up. But when I switch it off
it stays hot for an hour longer. This winter I used it
for 16 hours every day in a 20m2 room,
10 to 16 hours, with 240W input. With a conventional electric heater I would
need 550-600W for this. Here it was just 200-300W. Of course it depends on the
actual weather temperatures. At -10°C perhaps I’ll need 320W,
and if it’s +6°C, perhaps only 180W. That is the sum total
of my heating expenses. A second thing: I don’t want water
vapour to leak into the room although I must say there is
very little water vapour here. Nothing compared to dampness you would
need a dehumidifier to remove. Just a very, very minimal humidity output. So here I have designed a cover,
it is closed down here to collect the condensing water,
which drains off through this hose. The cover is mounted with 4 screws
so I can adjust the height. This gives me a heater size of 1m
with 3000cm2 of emitting surface, and that is sufficient for one room. I still switch it on and off by hand.
If you want to automate this you’d have to install a heater coil
instead of using a Bunsen burner. Then at the push of a button,
the coil would heat up the sand until it reached 60°C,
and then the gas would start. And this is safe, nothing can go wrong. Here you see a small hole on top
where unburnt gas could come out. Through entire winters
this hasn’t yet occurred. However this escaping gas would be
such a small amount that not even a Hydrogen sensor would react. This gas even pours through
concrete, it passes through everything. This is why storing this gas is very difficult,
and why I don’t like the idea of storing it, because imagine a tank filled with thousands
of litres of Hydrogen, and one spark… I wouldn’t want to be anywhere close by then! Here the setup is different:
I produce gas instantly, on demand. It is a constant, circular flow.
Now you may say, water is precious. But the water inside is not wasted at all. It stays within this circuit and
in the end I have water again. So we have this natural product water,
that is dissociated, split apart, and when it recombines and becomes
water again it produces heat. It is a constant circular flow
where the water is reused again. The same amount of water that is split apart
is what I get as vapour output and I can collect this and refill the DryCell. I could automate this with pressure switches,
temperature sensors, a thermostat and a small control system.
But there is not much to control. As soon as it reached the right room temperature
I’d let the heater run at 40W. And if the temperature drops,
it would power it up again to 200-300W. It is not so important
to be super-efficient here. Remember, these are
just the very first beginnings. 2 years ago I was invited to give a lecture
at the University of Natural Resources and Life Sciences in Vienna, Austria They were fascinated by my device. The only person who refused to enter the room
was the Professor himself. He was afraid something would explode. Later they all wanted to take courses so I built 8 DryCells with them. 3 months later the professor retired,
and his successor stopped the project. He was not interested in this topic at all. In these times of high tides
and crazy climate changes I can’t understand why people
still ignore things like this. Even with minimal trials
I have already gained decent efficiency. We are talking about
efficiency of 96-97% here. There are people in the US and Australia,
who even utilized this with resonance method. They saved much more energy
by using natural resonance and they made a lot of gas
with almost no energy input at all. One man even powered his car with it. He is dead now. The global players do not want this. So all we can do is
tinker in a small scale. Audience:
What do you call this machinery? It’s got a misleading name.
It is called a “DryCell”. But as you see, it’s not dry at all.
There is water inside. We have to distinguish it from earlier
“WetCells” with two electrodes in a water bowl. – Does this have anything to do with nuclear energy?
– No, nothing at all. I purchased a Geiger counter
from Nato times, still fully functional. It showed nothing. Nada. I then wanted to check for microwaves
and got a microwave detector,
along with this Geiger counter. I tried it on my microwave oven and
there was indeed a small leakage. I would say, you can safely use
a microwave oven, but not for cooking
because it destroys its nature. Outside the oven there was no big emission,
perhaps 0.4W below the oven. Then I tried it on my mobile phone
and just called myself. And you know what the detector said
about my mobile? More than 200 milliwatts! That is what we
hold against our head dozens of times a day! We have become used to them and
assume they won’t do any harm.
But that amount is really dangerous. But with the DryCell here, not even a hint of
microwave emission. Zero. Audience:
– The water powered car, what is that? – It is the global players who are developing this,
or who perhaps prefer not to! Almost every major company has
something with hydrogen up their sleeve. As you know, the fuel cell is en vogue now. One powers a fuel cell with Hydrogen
which then produces electricity for the engine. This would be a great and efficient thing. But we would still have to refuel! There was this inventor, Stanley Meyer,
who died mysteriously in 1987. He drove around in his water powered
beach buggy in public. There have been several others like him. As I said, this invention is 200 years old!
Imagine that, nothing has changed in over 200 years! Yes, everything has been spirited away,
cleared out, made extinct. Meanwhile NASA targets Mars. I recently met a young man
who volunteered for this project. A NASA flight to Mars with no return. He told me he was short-listed to being
among 250 of 700 applicants. And we can be sure they will use this technology!
In submarines and deep sea stations but not openly,
not here and now in this world, where we shall continue purchasing
oil, gas and coal. That’s the situation. Audience:
– So you are only using pure water as fuel? – Yes, this is nothing other than
pure water inside. – That’s way too cheap, isn’t it? This is why they don’t want to research
ways of improving the efficiency of this system. If a lot of people joined together to improve on
this system, then they will find a way. Especially if they have an urgent need
to do something for the climate then they’ll find an even quicker way.
If they want to. But I get the feeling,
they are not interested at all. Not the people, but those
who make big money from oil and gas. Here I have a catalytic converter. It works in the same way
my Sand Heater does. Audience:
What if I inhale this gas? Last year there was a 76 year old man
attending my lecture he had already built himself this type of cell.
He was ridden with arthritis, rheumatism, all that. He inhaled this Oxyhydrogen gas every day.
Oxygen and Hydrogen. He lost his arthritis, his joint problems,
he became fit as a fiddle! Here we have 30% pure oxygen.
We don’t have that much in the air. I pre-heat it just like I did before. Now I turn off the flame.
It makes a popping noise, and I start the gas output again.
Now… can you see that? It starts to glow.
There is no flame at all. Do you see that? Now the flame has come back. For this catalytic converter I would need
a very specific air/gas mixture. I can’t produce this right here. Can you see this? It is the gas only! No flame.
The Oxyhydrogen gas makes the platinum glow. With my Sand Heater I measured
temperatures of up to 750°C. That’s quite useful already, right? I also tried heating with catalytic converters
but it is difficult to provide the perfect air mixture. I do not want to use the air mixture right here,
as we would get nitric oxides. But when I burn pure Oxyhydrogen
there is no exhaust. Just pure water vapour. Nothing else. I think this is the only flame
that burns underwater. I’m sure you’ve never seen this!
A flame that burns underwater. It contains enough Oxygen
for stand-alone burning. Oxygen and Hydrogen. That’s all it needs
for burning underwater. Now watch as I submerge the flame.
Can you see this? The flame is underwater now. I pull it out again
and submerge it again. The water is getting warm. For maximum heat distribution the flame
needs to touch solid matter. In this way I have
already reached 90% efficiency. Have a check, you can feel
it is already warm. And I wasn’t yet at full power here. Ok, now the power supply
is running at full power. This makes a really long flame,
it reaches up to… oh, I get burned here. You can’t see the flame anymore,
but it stretches to perhaps here. Here I am already burning myself. And this is really just a miniature thing,
it’s not very big at all. But a cell like this still produces
double the amount required, so to heat a room it only needs
to run at half power. And with 4 cells like this
I could heat an entire house. Actually, I thought I could show you
all of this outside. Because I can also inflate balloons with this gas,
they will ascend to the sky. All of this is nothing other than water.
Split apart into a balloon, and up it goes. Camera operator:
– How many Watts do you need
for heating a house? – That depends on its insulation. Initially I thought I’d need
1 cubic metre of gas per hour. Which is a lot,
17 litres per minute. Currently I now think I can heat my
house with 600 litres per hour. (Audience)
– Over how long? – To keep it warm: 10 litres/minute,
that is 600 litres/hour. I need about 1.4kWh of
electricity energy per hour for this. That’s not very much. When I compare this with heating electrically
then I would need much more. In winter I heated 3 rooms with
infrared panels consuming a total of 4000kWh of electricity. And naturally when I heat with wood,
I need 18000 kWh during the winter for my house, for 6 rooms, 120m2. But it is hard to imagine things when I talk
about Watts, kWh or power, so perhaps I can explain it in clearer terms. We know that 1kg of beech wood
has 4.2kWh of heat energy. Now I can heat a room with much less than that
with my Sand Heater, this would be equivalent to
400g of beech wood over 24 hours and I don’t think anyone could heat
an entire room that frugally using just 400g of beech wood
keeping the place warm for 24 hours. That’s the efficiency I have. One solid cubic meter of wood has 1500 kWh
of energy. I need about 12-14 cubic metres per year. This is what any other wood burner
would consume on average. Wood is 4-5 times cheaper
than electricity. And why I have to save electricity. But it’s more than just
about affordability. I love having an emission-free heater.
That’s why I work on it. From producing electricity
you still get Carbon Dioxide,
mostly from coal-burning power plants. No! Not me!
I have photovoltaic panels,
3.5kWp, on the roof. That means I can make 4000kWh
of electrical energy every year that I can of course freely use for heating.
And I literally have zero emissions. Not totally this year, because I heated
75% electrically, but next year I will heat using
Oxyhydrogen only. I will have an estimated energy consumption
of about 2000kWh – for the entire winter season. This is laughable. This is 240 Euro,
that I don’t even have to pay for
because I have my solar power. If it wasn’t raining today I could have
shown you all of this better outside, I could have powered the entire setup
with one solar panel only. I have one with 240W power output,
that is half the output of this power supply.
Sufficient. Everyone talks about efficiency
like a litany, like a Mantra. Why? Let’s assume I make 1 litre of gas
with 133 to 140 Watts. A second litre of gas I get
entirely from solar power. That makes 2 litres for 140W,
or 1 litre of Oxyhydrogen for 70W. That would by over-efficiency, over-unity.
Just from the sun. The last little bit I need, I can additionally get
from the sunlight and it is done. That’s all I need. They teach us all in school this gas
is dangerous, because its combustible. Then an Australian comes and calls it
“Brown’s Gas”.
His name was Yull Brown. He copied US patents from the 1960’s and passed them off as his own. If there were still any patents,
they’d be long expired by now.
That was 60 years ago! There is no use in trying to
patent and hide this information anymore. That won’t make it public.
It can only evolve if anyone can build it. (Audience)
– Then it can be improved… – Yes, only then can it be improved upon! This is called “Open Source”.
Anyone can join in, replicate
and develop, free of charge. Now your heads are smoking, right? And what you may not realize is there are
thousands all over Europe building cells like this. Thousands and thousands of people!
In Germany, Switzerland, Spain, Portugal, France, while the general public still isn’t
aware of this at all. When I first stumbled upon this design
on the web, I was astonished. But it was not so easy for me back then,
all I had was a photo of something homemade. I had to imagine what was inside. I didn’t know anything,
I just gave it a go, and it worked. I made videos by myself,
then I got professional help from Andi and we started spreading this and making it
available for download on the web. Some quite some big names all
drove their cars with this. They all did. We never heard about them.
The media usually ignores them. What? I hear, one local newspaper might
print a story? As I said before, I don’t need mass media around me.
I prefer small groups of DIY hobbyists. Now I will show you one more thing. Stirling engines.
Here we are at model scale again. You just don’t get any large scale
high power Stirling engines. Even though this thing is so simple,
any fitter could replicate it. Just a few moving parts, that’s all. Here I have a Stirling motor model,
sinfully expensive, I think it was 98 Euro. It’s got no power output at all,
it can’t do anything useful,
but at least it moves. It’s a thermal engine. It converts heat
into mechanical energy which can then drive
power turbines or electrical generators. All large scale Stirling engines
are usually heated with wood pellets. I will also pre-heat this one. It’s common knowledge that a Stirling engine starts
when I heat it up with a flame. But what nobody seems to know
is that it works just as well without any flame!
Here we just have pure gas! See? I can pass my hand in between
and I won’t burn myself. This cylinder is coated with
something like platinum and palladium. Can you see this? Now all the large manufacturers
of Stirling motors have been trying for years to build
block heating power stations. But heating with wood pellets
soots up the engine. Their problem is the soot. Here we have no carbon particles.
No soot. No contaminants. Clean. No flame at all. The wire connecting the lamp has just come off.
But you see how the engine works. That’s just about the limit, hmm? The engine runs as long as I give it gas.
As soon as I move the gas away, it stops. Audience:
Can I make electrical energy with this? Yes, this Stirling engine
produces electricity. Since I began I’ve observed
how we’ve been mocked about everything,
from all sides. Be it by politicians… by everyone. It has been said that this flame could even
remove radioactivity and perhaps transmute matter. This is calcium hydroxide, lime. If you store it for 2 years
you get nuggets like this. Normally this is a powder. Now it is solid. Look what happens. This is called a lime light.
Incredibly bright. The funny thing is, the lime stays as it is.
It does not burn at all. It gets a bit more crumbly perhaps. Now I just heated up this lime 3 times in
an hour for about 130 seconds each time. And the room temperature kept stable. I calculated, this flame needs 300 Watt. Now how many Watt hours do I need
to heat a room with this lime? I just needed a fabulous 45 Watt hours! So the lime light is even more efficient
than the Sand Heater. But it would be rather complex.
You would have to enclose the lime into a tube, then we would have a flame here which needs
constant monitoring and control mechanisms. So theoretically speaking,
it is possible to heat up a room with 45Wh. What is 45Wh? 0.45 kWh for 10h/day! I wanted to show you another thing, too,
but we don’t have a magnet here. Place some carbon powder in here,
just carbon. Heat it up in the flame 2-3 times,
let it cool down and then try with a magnet.
What happens? It becomes fully magnetized! So this flame transmutes matter.
And other materials. – Does the lime get magnetized?
– No, lime remains lime. Imagine this: A few atoms of
carbon, 1-2 atoms of Hydrogen and we have iron. And other materials. I like unanswered questions.
I ask questions. People will find the answers. It’s good for you to leave with more
questions than you came with. Now let me ask you:
Is this information something we should discard? It’s not interesting, there’s no need for this…? We have oil and gas and nuclear energy!
Is the world really like this? As we all know, we have to reduce emissions.
Every country is obliged to do so. There are conferences,
climate certificates are traded. Now if we could heat
a house entirely emission-free, this would be a sensation, right? (Audience)
You forgot taxes, this is all just a business! With this I don’t even need a chimney.
I could build a house without such a funnel! There are no emissions at all! All I get in the end is water. This also makes building houses less expensive
without the need for a chimney. Common sense would call this a sensation. But it is not. Perhaps it is even fought about.
We do not know this for sure. We do not fight.
There is no need for that. We just do what we love,
we are just curious,
we want knowledge. And if it might be forbidden one day,
then so be it. I will rest assured
and relax in my rocking chair or play piano and wait, because the knowledge is out. The water energy wave will come,
no matter what, we just have to be patient.
It will overrun all of us. Most of the people searching for Free Energy
just think for themselves. What can I get, receiving, for myself… end of line… I started with a spiritual attitude. I considered what I could do
to make this world a bit better. I did not want anything for myself
but for everyone. I invested a lot of money and
all of my free time. But I have no technical background.
A lot of you will do it much better than me. Perhaps I have practical skills,
but I’m not a professional. The difference is:
I wanted to give. Donate what I have.
This is a very seldomly done act. And suddenly something strange happened. Things simply fell to me.
Right out of nowhere. I always find answers on the web,
I have ideas that turn out to be right, it feels like I get “provided with”, somehow things are “delivered”, effortlessly. This is the secret of amplitude, of wealth. The more I give,
the more I receive in return. People do not know this today. They all believe in a constant
lack of everything, feeling so poor. We should be feeling super-rich!
We are indeed rich, we are so richly gifted, and as soon as we start sharing these gifts
we will receive them back in multitude. This has been my personal experience
since I began taking part in this. And I believe that is why
I have succeeded so quickly. I am no better than anyone else. It is of another nature, and we should all become
more aware of this. Now, we have been sitting here
for long enough, it is time for action!
We have to work all day to get our cells done!

Leave a Reply

Your email address will not be published. Required fields are marked *