아크용접 으로 테이블만들기 2 [실전 생활용접 #3]

아크용접 으로 테이블만들기 2 [실전 생활용접 #3]


1.4t. Each pipe is still. We did a tech-weld, and the current value is… It’s going to be somewhere between 90 and 100. Then put the two cubes that were made. Release the transverse pipe. It’s the same way you make it at first. And here’s one more explanation. Any welding is almost the same, Especially with these thin corrugated And if you work with arc welding, There’s no gap between the two sides. It’s the easiest to make. It’s easy to do. And if this is any different, And it’s very likely to puncture. So I’m going to use these clamps. I’m going to make these two very close together. Welding is recommended. The first one I made a while ago, And then I hit him in the back. But now I’m gonna put the finishing touches on this. I’ll turn it over and weld it. He was bitten with a clamp in the same way. I don’t think we need to get clamped down here. I’ll do the same. And I’ll use a short welding rod again this time. It’s done like this. I’m going to give you one more explanation here. It’s a little bit of a setup that looks like the outside of this frame It’s not welded here. We’ll weld this place, and we’ll use the grinder. I can change it into a grinder. And I think most of the time, it’s a lot of the time. If we make this, we weld in here. Let it go. You can weld it and change it. Rather than welding and grinding. It’s not too messy to see gold like this. If I paint it later. So here we are. There’s one place left for the last time to weld. You can take this side off the inside. at this rate Based on the structure of this table, It’s not weak. So you just have to fill this place. Ah~ It’s not welded in here yet. We will continue to weld from here to the inside. We’re finished welding. If you look here, I just had a hole in the welding process. Even if it’s 1.5 t, it’s like this. You can get a hole if you’re a little vigilant. So when we make these products, It’s best to end it all at once. If there’s a hole like this, we’re gonna have to fill it up. Even if it’s welded, It’s more than done at once. Anyway, it’s even more messy. I’ll take the shit out of that place. I’ll try to make it up in a little while. It’s almost finished. You have to hold the wrong angle. in the right angle For example, there’s a twist like this way. It’s a little bit like that. Here’s the wrong part. Hold it. It’s held like this. And finally, the angle of the bridge is very different. We need to make sure it’s correct. And finally, I’m going to fill in the hole here. with a little non-useful welding rod. I’ll fill up the hole. If you look here, the hole’s filled. As you can see, it’s like this all at a time. It’s not as good as the welding is done. It’s a messier finish. So if you can, don’t let that hole go. It’s a good idea to work with great care. Today, we made a table. But it’s not the first time I’m working on it. It’s like this, you know, you can use it indoors. a little bit of a deadline. Making a table like this is not a good idea. Maybe it’s too far ahead. First of all, with this arc welding, I can make enough of these products. to show that I’ve made a table like this. If you have any other questions, Please ask me a question in the comments. I’ll give you a reply in my own way. I’ll stop here today.

8 thoughts on “아크용접 으로 테이블만들기 2 [실전 생활용접 #3]

  1. 테이블 신청 오늘 마감해서 추첨완료했습니다.

    이전 영상에서 신청하신 10분중 9번째로 신청하신 mi철계란 님이 당첨되셨습니다.

    당첨이 안되신 나머지 분들은 아쉽지만 다음에 또 기회를

    만들어 보겠습니다….^^

    감사합니다…

  2. 잘 봤습니다. 박판으로 생활가구/도구 만드는 영상 많이 올려 주세요! 도움이 많이 됩니다.

  3. 내공이 장난이 아니시네요. 정확하네요. 그리고 태이블도 정말 깔끔하네요. 하나 만들어보고 싶어지네요👏👏👏👍👍👍

  4. 영상 잘 봤습니다.
    어제 파이프로 연습 삼아 선반을 만들다 구멍이 나서 대충 때웠었는데
    못 쓰는 용접봉 같은 걸 대고 용접하는 방법이 있다니…
    좋은 정보 고맙습니다. 미당첨은 아쉽습니다. ㅠㅠ ㅎㅎ

  5. 용접후 그라인더로 다듬는것을 사상이라고 하나요?                                                                                                                            사상하실때 뭘로 하시는지 궁금합니다. 소개좀 해주세요                                                                                                                    그리고 사상요령 팁같은거 있으면 다음 영상때 부탁드립니다.

Leave a Reply

Your email address will not be published. Required fields are marked *