Hello, I’m an iron workshop. Today will be the third time for real life. As you saw in the video just now, Let’s make a table today. So far, we’ve been working on welding. I’ve given you some tips on how to practice. Now we’re going to move on to the actual work. And this table that I’m making right now, it’s not a problem. We’re going to draw one of the people who’s watching this. I’ll send it to you by courier. We’ll show you the results of the draw in the next video. under the title of “Apply You can leave a comment under this video. It’s good to subscribe with comments. Please tap it once. I would be grateful. And in the future, we’re going to be able to create these videos. And when something like this is made, It’s a product that’s available to subscribers who are watching the video. I’ll send it to you. Of course, this video is for the beginners of arc welding. That’s the video. But even if the beginners say, I’m going to go through the video that I uploaded earlier. You know, I’ve been practicing a little bit. It’s something you can do. So the basic parts that we’ve described earlier are the ones that we’re going to look at. I don’t explain it over and over again. Only the part that corresponds to this table operation at this time I’ll explain and proceed. Pipe size for today 30/30/1.4t It’s each pipe. Table size 600 / 400 height 320 I’m planning to make it. And the top one is Mulbau’s 24 t’s still. It’s a little thick, so it’s getting a little foggy. And the finishing seal will be black, matte-free. simple to use in the living room It’s called the tea table. And there’s an additional piece of rich material that’s being used. It looks like this. This is an accessory called the height control foot. So, the bottom of the bridge is like this way. You can go inside like this and finish it. It’s an accessory. This is something you can search for on the Internet under “Highlight Adjustment Foot.” It’s easy to buy. And when we make these iron tables, The easiest thing you can think of is… I’m going to make a 45-degree judgment like this. We’re going to meet each other like this way. Welded together, finished grinder. The legs go up here, they weld. He’s thinking a lot about these things. But today we’re going to be able to do this in a much easier way. I’m planning to make it. This is a foundation that I’m going to show you. There’s no 45-degree foundation like this. All you have to do is make a 90-degree decision. The pipe stillness that these four will be the table bridge. The legs are positioned like this. I finished the table. You can think of it as upside down. The next pipe across the bridge, It goes between the legs like this. And to the long side. I’ll go in like this. It’s a structure like this way. And when you build these table legs, Like you saw, like this. be more than the size of a plate There’s a way to make the table legs a little smaller. Or, for example, exactly the size of the top So this is exactly what the top size looks like. There is a way to make it the same size. It’s design-wise, it’s personal. It’s winning. But if this is the first time you’re working on it, It’s a little smaller than the size of the top. I can tell you it’s easier. If you make it, it could get a little off the angle. I’m afraid I can make something wrong. If the frame is a little smaller than the top, I can’t see the wrong part. That’s why I don’t feel any pressure. It’s an easy way to make it. This is the size. If you’re planning to make it the same size as the top, After you’ve mastered everything a little bit, I recommend you to make it. So I’m a little insecure today. So It’s a little smaller than the top. I’ll proceed. I don’t have much to do with arc welding these days. So, even if there’s a little bumpy part of the work Please excuse me. So when you’re going to weld it, for example, Assuming we’re going to have a volume here, Any work is the same. As part of the welding, this iron is Pull it. Pull like this. So it’s not a plane, but it’s not. 90 degrees like this. If we weld it here, it’ll be 90 degrees. This is the same. Pull it like this. If it doesn’t work well, Most of the time, this is a thermal transformation. The angle is wrong. When I worked on it without considering it, Things will be made wrong. I’m going to do two spangles here. I’m going to do two sprigs over here, too. Let me just give you a quick explanation He’s doing some kind of dressing. You know, I’m going to have to go to this place I’m going to do this here and here. by the way He thinks it’s his place. If you take a picture here, It’s going to be welded If you try, you’ll see. So he took it a little farther than he thought. Getting started might be a better way. It’s wrought like this. in this state of the moment You can weld this way. But novices are going to be able to see the directionally There are times when things work out Sometimes it doesn’t work. then When you make something that’s not as big as it is now, turning this around this It is also recommended to weld in a comfortable position. I’ll heat it up and take it. It’s welded like this. Let me ask you again about the clamp. with this bite If it’s the end of this way, I’m gonna make sure these parent metal shuts Welding can be carried out. welding sequence diagram He said there was a way to make it less angled. You know, just because I’m in this position right now If we go straight to the welding we saw here, It’s going to pull a lot. There’s no way we can do this right now. If you’re glued to this side, you’re gonna have to use the main graft to the back here. It is a good idea to weld the other side first. So I’m going to weld it here. And I want you to think about one thing. I’m shooting this place with this welding rod. This is a long welding rod, and I’ve just got a little bit of it. It’s a little easier to shoot. It’s a little easier to shoot because it’s 90 degrees. It’s relatively difficult to film here. If you’re trying to shoot this side with a long welding rod, He can’t film where he wants to be. Welding rod during welding process When welding in a well-positioned position, It’s not like we’re making a couple of these short weld rods. It could be a good way. I’m going to bite this short weld bar. This is more like a long welding rod. It’ll be easier to shoot. I’m going to make a clean one and take a picture. This isn’t a place where we’re going to do this, we’re going to do this. I’ve got a wig on this side. I’ll take 4-5 as my main dish. This is how I took it. And turn it. I’ll take another shot. Now it’s welded on both sides. One side’s a wig, but… It’s welded on this side and the other side. I’ve gained some weight in the area I’ve welded over here. You need to change this into a grinder. You change it like this. As you can see, we lost a little while ago. Now it’s a little bit off the outside. But you’re going to do the welding you saw here. This weld will pull a little bit. But when I hit him with a rubber hammer, When it opened a little bit, It’s a little bit open without having to be concocted again. It’s good to just weld in the condition. So we did a technique weld. It’s a good angle. when it’s done You can create another one of these.